HTML Sitemap & Scope Directory

Canadian construction estimating & takeoff portal

Dual-estimator QA, corporate credentials & team

Transparent Canadian pricing and starting fees

6-step dual-estimator takeoff and audit methodology

15-minute plan review and guaranteed fee quote

Direct Canadian dispatch, phone and email

Answers on turnaround, codes, software & files

Full catalogue of 22 CSI trade divisions

Coverage across all 10 provinces & 3 territories

In-depth commercial and residential bidding guides

Strict plan confidentiality and NDA commitments

PIPEDA and Quebec Law 25 cookie disclosure & preferences

Service agreement and proposal terms

Full-scope CSI MasterFormat and CIQS elemental estimates, quantity takeoffs, general requirements and bid-day levelling sheets for general contractors, developers and owners across Canada.

CEC-compliant electrical takeoffs covering 600Y/347V and 120/208V distribution, feeders, branch conduit and wire, lighting, fire alarm, solar PV and low-voltage systems, with labour units adjusted for Canadian crews.

Central boiler and chiller plants, welded carbon and stainless piping, hydronic loops, pumps and mechanical insulation, built with MCAA labour factors and registered to CSA B51 where pressure piping applies.

SMACNA sheet metal weight takeoffs, rooftop units, VAV boxes, VRF heat recovery, HRV/ERV ventilation, cold-climate heat pumps, kitchen and lab exhaust, and TAB allowances for HVAC contractors.

Underground DWV, cast-iron and PVC sanitary and storm risers, copper and PEX domestic water, commercial fixtures, interceptors, natural gas and CSA Z7396.1 medical gas takeoffs.

Coordinated mechanical, electrical, plumbing and fire protection takeoffs and clash-checked budgets that close the scope gaps between Divisions 21, 22, 23 and 26–28.

Wet, dry, pre-action, standpipe, fire pump, clean-agent and kitchen hood suppression takeoffs to NFPA standards referenced by the National Building and Fire Codes, with ULC-listed components.

Cubic-metre concrete volumes, formwork contact area, metric rebar tonnage (10M–35M), post-tensioned slabs, precast and tilt-up, pump time and cold-weather protection.

Unit counts for 190 mm and 290 mm block, modular brick veneer, grout volumes, bond-beam rebar, mortar, flashing and weeps, and scaffold or mast-climber time.

Piece-by-piece wide-flange and HSS tonnage, open-web steel joists, steel deck, connection allowances, stairs, handrails and crane erection takeoffs.

Board-foot and piece-count SPF framing, engineered LVL and I-joists, roof trusses, connectors, mass timber, and AWMAC-grade architectural millwork and cabinetry takeoffs.

Pitch-adjusted roof squares, tapered polyiso packages, TPO, EPDM, PVC and SBS membranes, standing-seam metal, asphalt shingles with eave protection, gutters and siding takeoffs.

Wall-type metal stud framing, ULC fire-rated gypsum assemblies, Level 4 and 5 finishing, acoustic ceilings, and spray foam, batt and rigid insulation takeoffs.

Room-by-room takeoffs with pattern waste for porcelain and ceramic tile, stone, LVT, sheet vinyl, carpet tile, hardwood, epoxy and polished concrete.

Primer and two-coat architectural painting, vinyl wallcoverings, dry-fall deck spraying, industrial coatings and intumescent fireproofing, priced to MPI standards.

Door-schedule audits for hollow metal and wood doors, electrified hardware sets, thermally broken storefronts, curtain wall, windows and overhead doors.

Existing-versus-proposed 3D cut and fill, swell and shrinkage, rock excavation, imported granular fill, trenching, shoring, erosion and sediment control, and excess-soil management.

Provincial and municipal spec roadwork in tonnes and square metres, granular base, curb and gutter, concrete storm pipe, PVC and ductile iron watermains, manholes and bridge takeoffs.

Caliper and container plant schedules, irrigation zones and mainline, permeable pavers, fencing and gates, site lighting, and pool takeoffs.

Traction and MRL elevators, solar PV and battery storage, structured cabling, access control and CCTV, commercial kitchens and signage takeoffs.

Selective interior demolition, full structural demolition with waste tonnage, asbestos, lead and mould abatement, and insurance-ready water and fire restoration estimates.

AACE Class 1–5 industrial estimates for process piping, oil sands and petrochemical plants, mining, water and wastewater treatment, tanks and pressure vessels.